Learn · Braking · 5 min read

Trail braking: how drivers carry the brakes into a corner

Ask someone how to drive a corner and they will usually describe three separate steps: brake in a straight line, let go of the brake, then turn. It is a good way to learn, and it is safe. It is also not quite what fast drivers do. Watch the pedal traces from a qualifying lap and the brake pressure does not drop to zero before the steering goes in. It fades away gradually, all the way to the middle of the corner.

That overlap between braking and turning is called trail braking: the brake pressure 'trails off' as the steering goes in. It is one of the techniques that separate a tidy lap from a fast one, and it follows directly from how a tyre shares its grip.

The friction circle

A tyre has a fixed amount of grip, and it can spend that grip in any direction: slowing the car, turning it, or a mix of the two. Engineers draw this as a circle. Straight-line braking uses the whole circle in one direction. A steady corner uses the whole circle sideways. Anything in between, some braking and some turning, sits on the edge of the circle at an angle.

The three-step method wastes part of that circle. In the moment between letting go of the brake and turning in, the tyres are doing neither job fully. Trail braking fills that gap: as the steering asks for more sideways grip, the brake gives some back, so the tyres stay close to their limit the whole way from the braking zone to the apex.

Braking later, and deeper

Because the car is still slowing as it turns in, it does not need to reach its corner speed before the turn-in point. Some of the speed is shed in the first part of the corner itself. That lets the driver brake a few metres later on the straight, which is time gained where the car is fastest.

The gain is not only in the braking zone. A driver who arrives at the corner with the brakes already off has to guess the entry speed exactly: too fast and there is no way left to scrub speed without running wide. A driver still lightly on the brakes can adjust the speed right up to the apex. Trail braking makes the entry more precise, not just later.

Helping the car turn

There is a second reason, and it has to do with weight. When a car brakes, its weight shifts forward onto the front tyres, and a tyre with more weight on it has more grip. Keeping a little brake on as the car turns in keeps the front tyres loaded at exactly the moment they need to grip, so the nose bites and the car turns more willingly.

Drivers call this rotation. A car that rotates well points towards the apex early, and the sooner it points down the road, the sooner the driver can open the steering and get back on the throttle. A car that will not rotate, that keeps pushing its nose wide, is said to understeer, and trail braking is one of the main tools for curing it from the cockpit.

The risk: too much, too long

The same weight shift has a downside. With the weight on the front, the rear tyres are lighter and have less grip. Brake too hard while turning, or keep the brake on too long, and the rear can step out. The car turns more than the driver asked for, and on a fast corner that can end in a spin.

So trail braking is about a smooth release, not about braking in the corner. The pressure should fall in a steady line as the steering angle rises, reaching zero around the slowest point of the corner. A sudden release upsets the car just as much as holding on too long: the weight springs back to the rear and the front loses the grip it was counting on.

Where it matters most

Trail braking earns the most in slow corners at the end of fast straights: hairpins and tight right-angle corners, where the braking zone is long and the entry speed is low. The car does a lot of slowing down, and moving even a small part of that into the corner frees up metres on the straight.

In fast sweeping corners there is very little braking to trail. The car might only lift off the throttle or touch the brakes briefly, and the line and the steering matter more. In a chicane the brake often stays on lightly through the first part to settle the car for the second.

Trail braking in the wet

In the rain, the circle shrinks. Every input has less grip to spend, and the car reacts more sharply when the driver asks for too much. Drivers still trail brake in the wet, but more gently: lower pressure, released earlier, with more of the slowing done in a straight line. The rear stepping out is a bigger risk on a slippery surface, and a mistake costs more.

How Lapdle models it

Lapdle's physics uses the friction circle directly. In Make the corner, the car can brake and turn at the same time, but every bit of braking takes away grip it could use for turning, and the other way round. A braking point that looks too late on a straight line can still work if the line gives the car room to finish slowing as it turns, and a braking point that works on one line can put the car off the road on another.

That is why the best runs in Make the corner rarely come from the earliest braking point. They come from braking late, turning in on a line that lets the car keep shedding speed, and reaching the apex at the right speed with nothing to spare.

Learning it

Drivers learn trail braking by doing less, not more. First they brake in a straight line and release fully before turning. Then they let the release overlap the turn-in by a fraction, a little more each lap, feeling for the moment the nose starts to bite. The goal is a single smooth movement: brake pressure going down as the steering goes in, the two inputs crossing over like a pair of dials.

More to learn